我是网红 我是广告主
我是网红 我是广告主

Lilly Schwartz YouTube网红频道详情与完整数据分析报告

Lilly Schwartz YouTube网红频道详情数据与分析报告 (数据更新时间 2020-03-23)
Lilly Schwartz
YouTube频道创建时间: 2013-05-18地区: 西班牙  语言: 英语 
486  1.04%
总观看量
1.53万  2.4%
平均观看量
493  2.49%
总视频数
31 
频道标签
粉丝全球排名
3,495,635th  (前 33.99%)
粉丝国家/地区排名
43,298th  (前 67.07%)
Nox评级
  1.39 
发布视频数
0  (最近一个月)
单月YouTube广告联盟收入
0元-0元
单个视频合作参考费用
24.58元
Lilly Schwartz YouTube频道数据统计 
Lilly Schwartz 粉丝量历史数据总览 (最近一年)
每日数据
累积数据
提示:由于YouTube只显示前三位粉丝数,所以曲线略有变化
Lilly Schwartz 观看量历史数据总览 (最近一年)
每日数据
累积数据
Lilly Schwartz 粉丝数和观看量每日对比 
7 日
30 日
观看量
粉丝数
近7天粉丝数增长量: 上个7天粉丝数增长量:
Lilly Schwartz 未来数据预估 (未来一年)
最近发布的30个视频互动率平均表现
视频观看量分布
平均观看量0
最热门视频 - 来源于 Lilly Schwartz YouTube网红频道
1823 观看量· 2019-06-28 视频发布时间· 114 点赞数· 33 评论数

This time I‘m showing you the finishing stages of my DIY WiFi Arduino darkroom timer and RGB enlarger light source. I tell you all about designing the final PCB board for the project and printing an enclosure for the darkroom timer. The finished project also includes the 3D print of a new enlarger head for my Durst M670 that can take a standard lightbulb. I can interface the timer with a WiFi switch to control my regular Durst heads or a LIFX smart bulb in the 3D printed head that can be controlled via WiFi. The 3D printed head connects to the enlarger via the stock M3 screws. If you want to know more about earlier stages of the project you can watch my vlogs here: https://www.youtube.com/playlist?list=PLmIKygCYwPmKsqzAApVswCnpiyZvLyXlz Also check out this blog post about the first prototype that was made out of RGB strip lights and a cardboard box: https://www.lillyschwartz.com/2018/04/01/darkroom-geekery-1/ Parts used for the final build: Arduino Mega (US) https://amzn.to/2J5inA0 Node MCU ESP8266 wifi chip (US) https://amzn.to/2NmqopF Waveshare 0.95 OLED display (US) https://amzn.to/2IWxOfa Adafruit 3x4 keypad (US) https://amzn.to/2IZbeCR 3x 10K Linear potentiometers (US) https://amzn.to/2XGnj7K 1x 10K resistor (buy an assorted pack) (US) https://amzn.to/2XdtC3B 1x 6.3mm jack socket (US) https://amzn.to/2RIlAcS 1x guitar foot switch (I use a non-latching Boss) (US) https://amzn.to/2XAdGHJ Mega Shield (my own design) LifX RGB Smart bulb (US) https://amzn.to/2NlQCZG Tp link HS-100 Smart plug for use with the regular enlarger head (US) https://amzn.to/2FIqK3E If you’d like to build an Arduino f-stop timer yourself I suggest you check out Brodie Tyrell’s open hardware and open source project: https://www.brodie-tyrrell.org/fstoptimer/ Personally I went with my own code, because I couldn’t find the components Brodie used and integrating different components just became too confusing. If you can find his exact components, no programming is necessary, which is the most difficult part. If you want to program it yourself, do yourself a favour and use an Arduino Mega from the start. There are no segmentation fault warnings on Arduinos, so if you run out of memory, it will just do random unpredictable stuff, which is a nightmare to debug. And you definitely will run out of memory on a regular Arduino unless you are a wizard at microcontroller memory management! If you want to have a go with my WiFi version and need pointers, contact me directly, I still have some PCB boards too. This is NOT an easy build though and the WiFi bits are not exactly straight forward to set up. You’ll probably find Brodie’s version much easier to build and better documented. Blog posts with further information on my build are coming soon though! Acknowledgements: Thanks to @frak, @196photo and my dad for help along the way! @frak helped with C++ refactoring problems, @196photo prevented the demise of my high power LEDs by pointing out that my LED driver might be unsuitable for them. My dad helped with the earliest stages of the project when I was still trying to figure out RGB strip lights and got a bit stuck with converting from an RGB colour space to RYB colour space. And of course this whole project would have been impossible without the Maker community and open source component libraries for Arduino! Building cool stuff is a community effort! Most importantly: Let’s not forget my husband, who supports me in all my crazy endeavours! Subscribe for more art videos, electronics builds and vlogs: http://bit.ly/2SfB5f9-subscribe If you enjoy my music, subscribe to my music channel Polarcoaster, where you can listen to it without all the additional fluff: https://www.youtube.com/channel/UC7vuEvqDlDGsg6XMbfRhaVA?sub_confirmation=1 *Recording Equipment* iPad Pro (US) https://amzn.to/2AMjCRl iPhone 5S (US) https://amzn.to/2M6kXqA Gooseneck Tablet Holder (US) https://amzn.to/2ST7llp ESDDI Ring Light (US) https://amzn.to/2VNUh2B Focusrite Scarlett Solo Studio (US) https://amzn.to/2DagrVv ✪ Many links I use are affiliate links, so you can support me at no extra cost to you! ✪ Or buy me a roll of film on Ko-fi: https://ko-fi.com/Q5Q1PY56 *Connect with me* Instagram: https://instagram.com/lilly.schwartz/ Twitter: https://twitter.com/lilschwartzart Facebook: https://www.facebook.com/lilschwartz/

最新视频 - 来源于 Lilly Schwartz YouTube网红频道
预估的受众粉丝年龄和性别分布 
预估的受众粉丝的地理位置分布 
NoxInfluencer团队

欢迎访问NoxInfluencer。商务合作、产品案例、或者有任何建议,可以在这里留言,我们会尽快给您回复。

通过facebook提问
(推荐)